A mining process that blasts land with water to remove the soil and expose minerals is. A. smelting. B. heap leaching. C. hydraulic mining. D. remediating.

Answer:

currently states that a person is qualified to drive a commercial motor vehicle if he/she “can read and speak the English language sufficiently to converse with the general public, to understand highway traffic signs and signals

So I think B

Answer: the absolute static pressure in the gas cylinder is 82.23596 kPa

Explanation:

Given that;

patm = 79 kPa, h = 13 in of H₂O,

A sketch of the problem is uploaded along this answer.

Now

pA = patm + 13 in of H₂O ( h × density × g )

pA= 79 + (13 × 0.0254 × 9.8 × 1000/1000)

pA = 82.23596 kPa

the absolute static pressure in the gas cylinder is 82.23596 kPa

There are a lot of ways employees uses in controlling exposure routes.  But when risk assessment is not be performed is not a part of the control methods.

The ways to control workplace hazards are known to be means taken to ensure safety in the workplace.

The examples are:

Learn more about exposure routes from

https://brainly.com/question/25799066

Answer:

When traveling at higher speeds (40 mph or faster), the most fuel-efficient way to keep the car cool is to follow these tips:

1. Use the vehicle's ventilation system: Instead of relying on air conditioning, use the car's ventilation system to circulate fresh air from outside. This helps to cool down the interior without putting extra load on the engine, thus saving fuel.

2. Close windows and sunroofs: To reduce wind resistance and drag, close all windows and sunroofs while driving at higher speeds. Open windows create drag, which can increase fuel consumption.

3. Park in the shade: Whenever possible, park your car in a shaded area to avoid excessive heating when it's not in use. This can help keep the car cooler and reduce the need for extra cooling when you start driving.

4. Use reflective sunshades or window tinting: Use reflective sunshades on your windshield and window tinting on side windows to reduce the amount of heat entering the car. This can help keep the interior cooler, reducing the need for excessive cooling while driving.

5. Maintain your vehicle: Regular maintenance, such as checking and replacing coolant, inspecting the radiator, and ensuring proper functioning of the engine cooling system, can help keep your car running efficiently and prevent overheating.

6. Plan your trips strategically: If possible, try to avoid driving during the hottest part of the day. By planning your trips to avoid peak temperatures, you can reduce the strain on your vehicle's cooling system and minimize the need for excessive cooling.

Remember that these tips are specifically focused on keeping the car cool while maintaining fuel efficiency at higher speeds. In certain circumstances, such as extremely hot weather, using the air conditioning sparingly may be necessary for passenger comfort, but it will increase fuel consumption.

The calculated mean value is 16. The sum of all values divided by the total number of values determines the mean (also known as the arithmetic mean, which differs from the geometric mean) of a dataset.

The term "average" is frequently used to describe this measure of central tendency. By dividing the sum of the given numbers by the entire number of numbers, the mean—the average of the given numbers—is determined. Mean is equal to (Sum of All Observations/Total Observations).

Mean=12+15+17+20/4

=16

Special road signage designate 10-cent zones. At the beginning and finish of the zone, there are signs. There is one space available for as long as three or four hours each day. Only specific hours of the day are subject to the 10 cent rate. There may be a Blue Zone in locations where paid parking is not (yet) in effect.

Learn more about mean here-

https://brainly.com/question/14882017

#SPJ4

The cluster head directs data transmission between clusters and controls the actions of its individual nodes.

The definition of power as the "capacity to accomplish work" refers to the capability to exert a force that compels an object to move. Even if the word is vague, it is clear what energy actually means: it is the force that causes objects to move. Kinetic energy and potential energy are the two categories of power.

Fossil fuels (coal, gas, and oil), nuclear energy, or renewable energy sources are the main energy sources. A secondary source of energy that is produced from fundamental energy sources is electricity.

To know more about  energy visit:

https://brainly.com/question/1932868

#SPJ1

Answer:

it is c) both (a) and (b)

Explanation:

True, ABS enables steering while using the most forceful stopping possible.

The most common material used in manufacturing, ABS is available in many different varieties. It can be extruded for CNC machining, turned into pellets for injection moulding, and filament for additive manufacturing.

Three monomers—acrylonitrile, butadiene, and styrene—combine to form ABS. A manufactured monomer made from propylene and ammonia is called acrylonitrile.

This element helps ABS maintain its heat stability and chemical resilience. Butadiene: It is created as a by-product of steam crackers, which generate ethylene.

The best driving conditions for ABS are dry, level surfaces. It aids the driver in applying the brakes as quickly as feasible while keeping the car under control. However, as the system repeatedly releases the brake, it can lengthen total stopping distances.

To know more about the ABS visit:

https://brainly.com/question/30838532

#SPJ4

The Cartesian and polar notation based on the information is solved below.

Cartesian notation:

P₁ - P₂ = (6cos(445°) - 2cos(460°))i + (6sin(445°) - 2sin(460°))j

≈ 3.43i - 2.91j

P₂ - P₁ = (-3.43)i + (2.91)j

Polar notation:

R1 = sqrt((6^2 + 2^2) - (262cos(460°-445°))))

≈ 3.91"

θ1 = atan2(6sin(445°) - 2sin(460°), 6cos(445°) - 2*cos(460°))

≈ -20.94°

R2 = sqrt((6^2 + 2^2) - (262cos(445°-460°))))

≈ 3.91"

θ2 = atan2(2sin(460°) - 6sin(445°), 2cos(460°) - 6*cos(445°))

≈ 159.06°

b) Cartesian notation:

P₁ - P₂ = (10cos(120°) - 4cos(40°))i + (10sin(120°) - 4sin(40°))j

≈ -5.74i + 8.66j

P₂ - P₁ = (5.74)i - (8.66)j

Polar notation:

R1 = sqrt((10^2 + 4^2) - (2104cos(40°-120°))))

≈ 11.18 cm

θ1 = atan2(10sin(120°) - 4sin(40°), 10cos(120°) - 4*cos(40°))

≈ 123.69°

R2 = sqrt((10^2 + 4^2) - (2104cos(120°-40°))))

≈ 11.18 cm

θ2 = atan2(4sin(40°) - 10sin(120°), 4cos(40°) - 10*cos(120°))

≈ -56.31°

c) Cartesian notation:

P₁ - P₂ = (4cos(4225°) - 3cos(45°))i + (4sin(4225°) - 3sin(45°))j

≈ -2.58i - 0.17j

P₂ - P₁ = (2.58)i + (0.17)j

Polar notation:

R1 = ✓(4^2 + 3^2) - (243cos(45°-4225°))))

≈ 4.14'

θ1 = atan2(4sin(4225°) - 3sin(45°), 4cos(4225°) - 3*cos(45°))

≈ -44

Learn more about Cartesian on

https://brainly.com/question/4726772

#SPJ1

To generate a series of read requests that have a lower miss rate on a 2 KiB 2-way set associative cache, we need to consider the cache parameters and access patterns. Let's analyze the cache listed above first:

Cache Data Size: 32 KiB

Cache Block Size: 2 words

Cache Access Time: 1 cycle

To reduce the miss rate on a 2 KiB 2-way set associative cache, we can consider the following factors:

Cache Size: The size of the cache affects its capacity to store data. Since the 2 KiB cache is smaller than the 32 KiB cache listed above, it may result in a higher miss rate. To generate read requests with a lower miss rate, we can focus on utilizing the available cache space efficiently.

Cache Block Size: The block size determines the amount of data fetched from memory into the cache on a cache miss. A larger block size can improve spatial locality and reduce miss rates. However, it can also lead to more capacity misses if the cache is not large enough to hold multiple blocks from the same memory region.

Access Patterns: The pattern of memory accesses can greatly impact cache performance. Sequential and localized access patterns tend to have lower miss rates compared to random or scattered access patterns. By designing read requests that exhibit good spatial and temporal locality, we can improve the cache's hit rate.

One possible solution to make the listed cache have an equal or lower miss rate than the 2 KiB 2-way set associative cache is to increase its associativity. The given cache is direct-mapped, meaning each memory block can only map to one specific cache block. By making the cache set associative (e.g., 2-way set associative), each memory block can map to two cache blocks instead. This allows for more flexibility in caching data and reduces the likelihood of capacity misses.

Advantages of increasing cache associativity:

Reduced miss rate: The cache can accommodate more data with increased associativity, improving the hit rate and reducing cache misses.

Improved spatial locality: Higher associativity allows for better utilization of cache space, increasing the likelihood of neighboring memory blocks being present in the cache.

Disadvantages of increasing cache associativity:

Increased complexity and cost: Higher associativity requires additional hardware, such as additional cache lines and comparators, which increases the complexity and cost of the cache design.

Increased access latency: The cache access time may increase due to the additional hardware and the need for more complex cache indexing and replacement policies.

It's important to note that the actual impact on the miss rate and cache performance depends on the specific access patterns and characteristics of the workload. Analyzing the workload and considering factors such as cache size, block size, and associativity can help in designing an optimized cache system with a lower miss rate.

Learn more about   set associative cache,  from

https://brainly.com/question/31986104

#SPJ11

Answer:

a) The amount by which this specimen will elongate in the direction of the applied stress is 0.466 mm

b) The change in diameter of the specimen is  - 0.015 mm

Explanation:

Given the data  in the question;

(a) The amount by which this specimen will elongate in the direction of the applied stress.

First we find the area of the cross section of the specimen

A = \(\frac{\pi }{4}\) d²

our given diameter is 20.5 mm so we substitute

A = \(\frac{\pi }{4}\) ( 20.5 mm )²

A = 330.06 mm²

Next, we find the change in length of the specimen using young's modulus formula

E = σ/∈

E = P/A × L/ΔL

ΔL = PL/AE

P is force ( 46300 N), L is length ( 201 mm ), A is area ( 330.06 mm² ) and E is  elastic modulus (60.5 GPa) = 60.5 × 10⁹ N/m² = 60500 N/mm²

so we substitute

ΔL = (46300 N × 201 mm) / ( 330.06 mm² × 60500 N/mm² )

ΔL =  0.466 mm

Therefore, The amount by which this specimen will elongate in the direction of the applied stress is 0.466 mm

(b) The change in diameter of the specimen. Indicate an increase in diameter with a positive number and a decrease with a negative number.

Using the following relation for Poisson ratio

μ = -  Δd/d / ΔL/L

given that Poisson's ratio of the metal is 0.33

so we substitute

0.33 = -  Δd/20.5 / 0.466/201

0.33 = -  Δd201 / 20.5 × 0.466

0.33 = - Δd201  / 9.143

0.33 × 9.143 =  - Δd201

3.01719 = -Δd201

Δd = 3.01719 / - 201

Δd  = - 0.015 mm

Therefore, The change in diameter of the specimen is  - 0.015 mm

Answer:

using standardized parts

Explanation:

Answer:

Can I be it plzzzzz!?

Explanation:

I need points

The device that sends packets of data through different networks, ensuring they reach the correct address, is a router.The correct answer is option D.

A router is a networking device that operates at the network layer (Layer 3) of the OSI model. Its primary function is to forward data packets between different networks based on the destination IP address.

When a packet arrives at a router, it examines the destination IP address and uses its routing table to determine the appropriate outgoing interface or next hop for the packet.

The router then encapsulates the packet in a new data frame and sends it to the next network on its path. This process is repeated at each router along the route until the packet reaches its final destination.

Routers are essential for connecting multiple networks and enabling communication between devices on different subnets or networks. They perform intelligent packet routing, allowing data to flow efficiently across complex network topologies.

Additionally, routers provide security features like network address translation (NAT) and firewall capabilities to protect the connected networks.

In conclusion, a router is the correct device that sends packets of data through different networks while ensuring they are correctly addressed and delivered to the intended destination.

For more such questions router,click on

https://brainly.com/question/29564882

#SPJ8

Answer:

Q=I^2Rt

Explanation:

The principle of resistance welding is the Joule heating law where the heat Q is generated depending on three basic factors as expressed in the following formula

Q=I^2Rt

I is the current passing through the metal combination

R is the resistance of the base metals and the contact interfaces

t is the duration/time of the current flow.

Answer: 2nd Student (Ceramic student)

Explanation: Ceramic is reliable for fuses more than the paragraph in this states they are. Hence it would be the 2nd student who is wrong.

In Excel, to build a dashboard we need to add a tab and label it as Dashboard. Then, we set a gray background and copy-paste the three pivot charts we have built in the previous steps. Also, we insert slicers for Employee Last Name and Region.

We ensure these slicers dynamically interact with all three charts by selecting each slicer, right mouse clicking, choosing report connections, and selecting the appropriate check boxes. Finally, we test the dashboard to ensure that all of the charts interact with the slicers and when we drill down into the region and employee last names we see the corresponding pivot tables dynamically update as well.The steps to build a dashboard in Excel are as follows:

Step 1: Add a tab and label it as Dashboard

Step 2: Set the gray background

Step 3: Copy-paste the three pivot charts we have built in the previous steps

Step 4: Insert slicers for Employee Last Name and Region

Step 5: Ensure these slicers dynamically interact with all three charts by selecting each slicer, right mouse clicking, choosing report connections and selecting the appropriate check boxes

Step 6: Test the dashboard to ensure that all of the charts interact with the slicers

Step 7: When we drill down into the region and employee last names we see the corresponding pivot tables dynamically update as well.To create a dynamic dashboard, it is important to choose the correct chart types, slicers, and chart sizes and locations. Slicers are used to filter the data in the pivot tables and charts. Charts in Excel can be easily resized, formatted, and customized to make it more attractive and informative to users.To ensure that all of the charts interact with the slicers, we should select each slicer and check if the charts are changing accordingly. Finally, we need to test the dashboard to ensure that it is working as expected.

To know more about Excel visit:

https://brainly.com/question/30324226

#SPJ11

**The self-test in Chapter 4 of the book "Electronic Devices Conventional Current Version, 9th Edition" by Thomas L. Floyd is a valuable resource for reviewing electronics engineering concepts and preparing for board exams.** It provides comprehensive coverage of bipolar junction transistors, a fundamental component in electronic circuits.

This self-test can serve as a valuable tool for assessing your understanding of key concepts related to bipolar junction transistors. By working through the questions and evaluating your answers, you can identify areas that require further study and gain confidence in your knowledge.

However, it's important to note that relying solely on this self-test may not be sufficient for thorough exam preparation. It's advisable to supplement your review with additional resources, such as textbooks, lecture notes, and practice problems from various sources. This will ensure a well-rounded understanding of the subject matter and increase your chances of success on the board exam.

Learn more about Electronic Devices here:

https://brainly.com/question/33320486

#SPJ11

Unwelcome and severe actions constitute quid pro quo or assault, while pervasive actions create a hostile work environment.

In legal claims of harassment, there are specific requirements that need to be met to establish the validity of the claim. One such requirement is that the actions must be unwelcome and severe, occurring multiple times either to the individual making the claim or to multiple individuals. These types of actions, commonly known as quid pro quo or assault, involve situations where there is an explicit or implicit demand for favors or sexual acts in exchange for employment benefits or where physical or verbal conduct creates a hostile and intimidating work environment.

Another requirement for legal claims of harassment is the creation of a pervasive and hostile work environment. This means that the actions or behavior of the harasser must be persistent, frequent, or continuous, resulting in an environment that is intimidating, offensive, or abusive. Such an environment negatively affects the victim's ability to perform their job effectively and comfortably.

Learn more about claims of harassment

brainly.com/question/14695534

#SPJ11

The current in the circuit would be approximately 10,958.33 A.

Ohm's law states that the "current in a circuit is equal to the voltage applied to the circuit divided by the total resistance of the circuit".

To solve this problem, we need to first determine the total resistance of the two resistive heating elements in the circuit.

Since the heating elements are connected in series, their resistances add up, so the total resistance of the circuit is

⇒ 2 x 2.8 kW / 250 V = 11.2 kW / 250 V = 0.0448 kW / V.

As per Ohm's law, the current in the circuit would be

⇒ 492 V / 0.0448 kW / V = 10,958.33 A.

Therefore, the current in the circuit would be approximately 10,958.33 A.

To learn more about Ohm's law click here:

https://brainly.com/question/1247379

#SPJ2

The Digital Processing is not part of the OBD II implementation.

OBD II is known to be a kind of acronym for On-Board Diagnostic II. This is known to be the second generation of on-board self-diagnostic equipment that is needed for light- and medium-duty California vehicles.

The OBD-II is said to be a kind of on-board computer that handles emissions, , speed, etc.

learn more about  OBD II implementation from

https://brainly.com/question/14281435

Companies that use renewable resources, reduce emissions of harmful chemicals into the environment, and help other firms reduce their waste have taken advantage of sustainable practices or sustainable initiatives.

Yes, companies that use renewable resources, reduce emissions of harmful chemicals into the environment, and help other firms reduce their waste are engaging in environmentally-friendly practices. the negative impact of business operations on the environment.

Using renewable energy sources such as solar, wind, or hydroelectric power Implementing energy-efficient measures to reduce energy consumption Recycling and properly disposing of waste materials to minimize landfill waste Using eco-friendly materials and products that have a lower environmental footprint.

To know more about environmentally-friendly:- https://brainly.com/question/1229721

#SPJ11

The capacitance is affected is that the capacitance increases because of the insertion of Teflon.

A capacitance is known to be a form of a device that is said to be used to save some measures of charges in any kind of an electrical circuit.

Note that the capacitor functions on the principle that the capacitance of a conductor is said to go up if an earthed conductor is  taken close to it.

Therefore, The capacitance is affected is that the capacitance increases because of the insertion of Teflon and so the teflon tends to widen the capacitance.

Learn more about capacitor from

https://brainly.com/question/13578522

#SPJ1

Answer:

the liquid woulriekwvhrnsshsnekwb ndrhwmoadi

The  option that has the correct order or sequence of events are;

1) Scan host.

2) Add host to subscription.

3) Use host as report source.

Host assets are known to be a kind of IP addresses in a person's account. This type of assets is one that can be used as a kind of  scan, map and also to report targets.

A person can view the hosts in their account by going the  Assets panel to  the Host Assets. One can add new hosts by the use of the New menu. The person can also only carry out actions like scanning, mapping and reporting on one's hosts.

Learn more about IP addresses from

https://brainly.com/question/24930846