Firebrick is referred to as "common brick" because it is the most commonly used

type of brick.

Answer:

Use GitHub or stackoverflow for this answer

Explanation:

It helps with programming a lot

Answer:

  entering drivers

Explanation:

Drivers entering a traffic circle must yield the right-of-way to those already in the traffic circle. (Among other things, this rule helps avoid gridlock.)

Answer:

Answer:

10.007

Explanation:

Assuming we have to find out the compression ratio of the engine

Given information

Cubic capacity of the engine, V = 245 cc

Clearance volume, V_c = 27.2 cc

over square-ratio = 1.1

thus,

D/L = 1.1

where,

D is the bore

L is the stroke

Now,

Volume of the engine V =\(\frac{\pi}{4} D^2L\)

plugging values we get

245 = \(\frac{\pi}{4} D^3/1.1\)

Solving we get D =7 cm

therefore,  L= 7/1.1 =6.36 cm

Now,

the compression ratio is given as:

r =(V+V_c)/V_c

on substituting the values, we get

r = (245+27.2)/27.2 =10.007

Hence, Compression ratio = 10.007

The flow rate beneath the dam per day per meter of dam out-of-plane is approximately 0.864 m³/day.

To calculate the flow rate per day beneath the dam per meter of dam out-of-plane, we can use Darcy's law, which relates the flow rate (q) to the hydraulic gradient (i) and the coefficient of permeability (k).

The formula for Darcy's law is:

In this case, we need to calculate the flow rate per day per meter of dam out-of-plane.

Let's assume the cross-sectional area is 1 square meter (m²). We also need to determine the hydraulic gradient (i).

The hydraulic gradient can be calculated by finding the difference in head (h) between the upstream and downstream ends of the dam, and dividing it by the length of the dam (L).

In this case, the length of the dam is 10 meters (m).

Let's assume the head difference is 2 meters (m).

Therefore, the hydraulic gradient (i) would be:

Now we can substitute the values into Darcy's law equation:

To convert the flow rate from cm³/s to m³/day, we need to multiply it by the conversion factor:

Therefore, the flow rate beneath the dam per day per meter of dam out-of-plane would be approximately 0.864 m³/day.

Learn more about flow rate beneath

brainly.com/question/9874441

#SPJ11

When an aircraft is loaded 90 pounds or more than the maximum certificated gross weight and fuel (avgas) is drained to bring the aircraft weight within limits, 15 gallons of fuel should be drained.

To learn more about aircraft loaded moment refer to:

https://brainly.com/question/28250039

#SPJ4

Humanistic perspective. A psychological standpoint that focusses on the originality of the individual and believe that human beings possess an innate inclination to improve and to confine their lives through the decisions they make. Sometimes named the "third force" in psychology.

Humanistic psychology is a philosophy that emphasizes looking at the whole individual and highlights concepts such as free will, self-efficacy, and self-actualization. Rather than focusing on dysfunction, humanistic psychology aims to help people fulfill their possibility and maximize their well-being.

The humanistic perspective on character emphasizes the individualized grades of optimal well-being and the use of creative potential to help others, as well as the relational conditions that promote those grades as the outcomes of healthy development.

To learn more about humanistic perspective, refer

https://brainly.com/question/28192990

#SPJ9

Answer:

The GMAW process commonly uses a constant voltage power source (GMAW-CV) that allows for a relatively constant welding voltage output over a range of welding currents. For GMAW-CV the welder selects the wire feed speed (WFS) on the wire feeder unit and an appropriate voltage on the welding power supply.

Answer: 150m

Explanation:

The following can be depicted from the question:

Dimensions of outer walls = 9.7m × 14.7m.

Thickness of the wall = 0.30 m

Therefore, the plinth area of the building will be:

= (9.7 + 0.30/2 + 0.30/2) × (14.7 × 0.30/2 + 0.30/2)

= 10 × 15

= 150m

The plinth area will be 150m.

Given information

Dimensions of outer walls = 9.7m × 14.7m.

Thickness of the wall = 0.30 m

Plinth area of the building = (9.7 + 0.30/2 + 0.30/2) × (14.7 × 0.30/2 + 0.30/2)

Plinth area of the building = 10 × 15

Plinth area of the building = 150m

Therefore, the Option A is correct.

Read more about Area

brainly.com/question/25292087

GIS

The full for GIS is : Geographic Information System.

The GIS is a system of mapping that is used to create, analyze, manage and map all the types of data.

It is a method capturing, checking as well as displaying all the data that is related to the position of the surface of earth.

Remote Sensing

Remote sensing is defined as a process where the various physical characteristics of an area are constantly monitored and detected by a process of measuring the reflection of the emitted radiations at ta distance.

The snow covered areas of the Kabul basin can be monitored and analyzed by using the process of GIS and remote sensing.

They provide a continuous source of information and data about snow covered peaks, the amount of snow to the authorities.

Learn More :

https://brainly.in/question/1556256?__cf_chl_captcha_tk__=pmd_2d2d9994422ca43d3cbbcf6322e6c34da175405a-1628654009-0-gqNtZGzNAvijcnBszQ3i

Answer:

The application of regulations in locations are very important.

Explanation:

The application of regulations in locations are very important in order to gain more benefit from it because people choose those places that are well regulated and having more facilities. If the location has baths, showers, electric floor heaters and other necessities so the people prefer the place over another and increase of clients occurs which give more benefits to the place owners.

Answer:

i think 1844

Explanation:

2005 BMW 5 Series , that should be it

The script in Java that execute the above output is:

 import   java.util.LinkedList;

import  java.util.Scanner;

class ListItem {

   String data;

   ListItem next;

   public ListItem(String data) {

       this.data = data;

       this.next = null;

   }

   public void printNodeData() {

       System.out.println(data);

   }

}

public   class GroceryShoppingList{

   public  static void main(String[] args){

       LinkedList  <ListItem> shoppingList =new LinkedList<>();

         Scanner scanner =new Scanner(System.in);

       // Read items from input and add them to the shoppingList

       String item = scanner.nextLine();

         while(!item.equals("-1")) {

           ListItem   listItem =new ListItem(item);

           shoppingList.add(listItem);

           item = scanner.nextLine();

       }

       // Output each item in shoppingList

       for (ListItem listItem : shoppingList) {

           listItem.printNodeData();

       }

   }

}

You can compile and run this code,and it will prompt you to enter items for   the shopping list.

Once you enter all the items and input -1,it will print each item from the   shopping list on a new line.

The above code helps create and maintaina grocery shopping list by allowing the user to input   items and printing them out.

Learn more about Java at:

https://brainly.com/question/26789430

#SPJ4

The SELECT INTO statement allows you to create a new table based on the columns and data from an existing table. The syntax for this statement is as follows:
SELECT * INTO newtable [IN externaldb] FROM table1;

In this statement, "newtable" is the name of the new table you want to create, "externaldb" is the name of an external database (if you want to create the new table in a different database than the original table), and "table1" is the name of the existing table you want to copy.

For example, if you want to create a backup copy of the "Customers" table in a separate database called "Backup.mdb", you could use the following statement:

SELECT * INTO CustomersBackup2013 IN 'Backup.mdb' FROM Customers;

This would create a new table called "CustomersBackup2013" in the "Backup.mdb" database, with all of the columns and data from the "Customers" table.

Alternatively, if you only want to copy certain columns from the original table, you can specify those columns in the SELECT statement:

SELECT CustomerName, ContactName INTO CustomersBackup2013 FROM Customers;

This statement would create a new table called "CustomersBackup2013" with only the "CustomerName" and "ContactName" columns from the "Customers" table.

Finally, if you want to rename the columns in the new table, you can use the AS clause in the SELECT statement:

SELECT CustomerName AS Name, ContactName AS Contact INTO CustomersBackup2013 FROM Customers;

This statement would create a new table called "CustomersBackup2013" with two columns: "Name" (renamed from "CustomerName") and "Contact" (renamed from "ContactName").

You can learn more about databases at: brainly.com/question/30634903

#SPJ11

Therefore, we can design the circuit using two 2:1 multiplexers as a two-bit adder under the given conditions.

Yes, I can design the circuit using the given conditions. Here are the details of the work:

Truth Table:

Let's use A and B as inputs, S as sum, and C as the carry. The truth table is given below:

A B S C0 0 0 00 1 1 00 1 0 11 0 1 01 1 0 1

Simplification K-Map/Implementation Table

:From the truth table, we can get the following equations:

S = A'BC' + AB'C + ABC' + ABC = AB + AC + BC'

Implementation table is given below:

AB C S000010011001101111

Logic Circuit:

We can use the two available 2:1 multiplexers to implement the circuit. Here is the logic circuit diagram:

Therefore, we can design the circuit using two 2:1 multiplexers as a two-bit adder under the given conditions.

To know more about multiplexers visit:

https://brainly.com/question/15052768

#SPJ11

we need to use the Fresnel equations. Since the wave is incident normally (perpendicular) to the boundary, we can use the simplified equation for the reflection coefficient, given by:

R = (E1r - E2r) / (E1r + E2r)

What is the reflection coefficient?
Where R is the reflection coefficient, E1r is the relative permittivity of region 1, and E2r is the relative permittivity of region 2. Given that region 1 is a lossless non-magnetic dielectric with relative permittivity &r = 3.24, and region 2 is free space with a relative permittivity of 1, we can plug in the values:

R = (3.24 - 1) / (3.24 + 1)

R = 2.24 / 4.24

R ≈ 0.528

Thus, the reflection coefficient is approximately 0.528.

Next, to find the transmission coefficient (T), we can use the relation:

T = 1 - R

T = 1 - 0.528

T ≈ 0.472

Therefore, the transmission coefficient is approximately 0.472.

to know more about transmission coefficient:

https://brainly.com/question/31412413

#SPJ11

Answer:

Explanation:

The process that Piaget called "adding another example to an existing scheme" is called assimilation. Assimilation refers to the cognitive process of incorporating new information or experiences into existing mental schemas or frameworks. In this case, Tammy assimilates the new example of a golf ball into her existing "ball" scheme, expanding her understanding of what falls under the category of a ball.

Its True the range before you enter data saves time because it confines the movement of the active cell to the selected range .

What is data
Data is information that has been collected and organized in a meaningful way. Data can be quantitative (numbers) or qualitative (descriptive and subjective information). Data can come from surveys, experiments, observations and other sources. Data is a valuable asset and is used to inform decisions, create insights, and uncover trends and patterns. Data can be structured (structured in a way that makes it easy to search, sort, and analyze) or unstructured (not organized in a conventional way). Data can be used to identify problems, generate and test hypotheses, and measure the success of different strategies. Data is a key component of any organization and is used to help inform decisions, gain insights, and improve operations.

To know more about data
https://brainly.com/question/10980404
#SPJ4

Using MATLAB's ode45 solver to solve and plot the differential equation is following:

% Define the differential equation

dydt = (t, y) 3*y + 4*y*t;

% Define the initial condition

y0 = 1.0;

% Define the time span

tspan = [0, 0.5];

% Solve the differential equation

[t, y] = ode45(dydt, tspan, y0);

% Plot the solution

plot(t, y)

xlabel('t')

ylabel('y')

title('Solution of y'' = 3y + 4yt')

2. Writing the MATLAB script to plot the y(t) function with t = 0: m/50: 25m, where y = -0.05 cos(t):

% Define the time span

t = 0:pi/50:25*pi;

% Calculate the y values

y = -0.05*cos(t);

% Plot the y(t) function

plot(t, y)

xlabel('t')

ylabel('y')

title('Plot of y(t) = -0.05cos(t)')

Learn more about differential equation here:

brainly.com/question/32524608

#SPJ4

Answer:

sandals, gloves, necklaces

Explanation:

sandals, gloves, necklaces

I don't know how?

i hate it that it says 20 charcters long

Answer:

a

Explanation:

6.25×10⁻¹⁸ electrons will flow through a copper wire.

Electrons can be defined as the sum of atomic particles that is the career of negative charge, they are responsible for the chemical property of an element, the electrons are present in the shell.

Use formula ( I = ne/t )

Here,

number of electron

electron =1.6 x 10¯¹9 C

We have a relation between charge and current as

Charge = Current×time i.e

Q = i×t.

Now we have current = 10 amp & time = 10sec from given data.

Therefore charge Q = 10×1 = 100 coulombs.

Again we have a relation between charge and no of electrons

I.e no of electrons= total charge / 1.6×10⁻¹⁹

So, no of electrons = ( 100C/1.6×10⁻¹⁸ )

= 6.25×10⁻¹⁸ electrons.

Therefore, 6.25×10⁻¹⁸ electrons will flow through a copper wire carrying 10 amps current for 10 sec

Learn more about electrons, here:

https://brainly.com/question/1255220

#SPJ1

The best practice that Raven should follow is to use DC2 or DC3 as the Domain Naming Master of the following is a best practice that Raven should follow. The correct option is A.

The management of the addition or deletion of domains from the forest is the responsibility of the Domain Naming Master. For redundancy and fault tolerance, it is advised to split the FSMO roles among several domain controllers.

Since DC1 already has a copy of the global catalog, it is advantageous to choose a different domain controller (DC2 or DC3) as the Domain Naming Master to disperse the workload and guarantee high availability. This ensures that the forest's operations may continue even if one domain controller goes offline and prevents the creation of a single point of failure.

Thus, the ideal selection is option A.

Learn more about Domain Naming Master here:

https://brainly.com/question/31558740

#SPJ4

The component that is commonly used to stabilize the steering of some light trucks and four-wheel vehicles is called a "stabilizer bar" or "sway bar".

What is vehicles?
A vehicle is any means of transportation that is used to transport people, goods or both from one place to another. Vehicles can come in various forms such as cars, trucks, buses, motorcycles, bicycles, airplanes, boats, trains, and more. Vehicles can be powered by different sources such as fossil fuels, electricity, and human power. The primary purpose of vehicles is to provide transportation to people and goods efficiently and effectively, saving time and effort in moving from one place to another.

The stabilizer bar is a metal component that is installed as part of the vehicle's suspension system. It is typically positioned between the left and right wheels and is attached to the control arms or struts of the suspension.
During turns, the weight of the vehicle shifts to one side, causing the suspension on that side to compress and the other side to extend. This can lead to body roll and sway, which can affect the handling and stability of the vehicle.The stabilizer bar helps to counteract these forces by transferring some of the weight and force from the compressed side of the suspension to the extended side. This helps to keep the vehicle more level during turns, reducing body roll and sway and improving the vehicle's handling and stability.

To know more about force visit:
https://brainly.com/question/28875770
#SPJ1

Answer:

Explanation:

I'm not 100% this is what you want, but here it is:

2

3

13

8

11

A

13

Answer:

The company will have $311,424 in its investment set-aside account.

Explanation:

To determine the amount of money that the company will have after 7 years with an interest rate of 11% per year, we must calculate the price to start with an increase of 11%, and then repeat the operation until reaching seven years:

Year 0: 150,000

Year 1: 150,000 x 1.11 = 166,500

Year 2: 166,000 x 1.11 = 184,815

Year 3: 184,815 x 1.11 = 205,144.65

Year 4: 205,144.65 x 1.11 = 227,710.56

Year 5: 227,710.56 x 1.11 = 252,758.72

Year 6: 252,758.72 x 1.11 = 280,562.18

Year 7: 280,562.18 x 1.11 = 311,424

The amount of money that the company will have in its investment set-aside account is; $311424

Formula for the future value is;

F = P(1 + i)ⁿ

Where;

F is Future value

P is Present value

i is interest rate

n is Time

The four engineering economy symbols and their values from the question are;

F = ?

P = $150000

i = 11% = 0.11

n = 7 hours

Thus;

F = 150000(1 + 0.11)⁷

F = $311424

Read more about future value at; https://brainly.com/question/5303391

Default argument is the correct option among the given alternatives. The functionality of an automatically assumed zero payment when the user doesn't enter the amount paid is an example of a default argument.

What is a default argument? A default argument is a value assigned to an argument in a function definition in Python. If the user doesn't provide a value for the argument in a function call, the default value is used. It's important to note that the default argument is the last argument in the parameter list. The following is the syntax: Syntax: def function name(parameter1, parameter2=default value):The default argument is assigned a value during the function definition process. When the function is called, the user may supply a different value for the argument. When the function is called without any arguments, the default value is used. This is the functionality that is seen in the given code, which is the example of a default argument. The write amount() function is defined with two arguments, name and amount, the latter of which is assigned a default value of 0. If the user does not supply a value for amount when calling write amount(), the default value of 0 is used. This is a typical use of default arguments in Python.

To know more about default argument visit:

https://brainly.com/question/32335628

#SPJ11