Martha has been running a small business for two years. She now seeks additional investment to finance her business. She has found potential investors who want to check how much Martha's business owns and owes others. Which financial statement should Martha provide to her investors? A. cash flow statement B. balance sheet C. trial balance D. journal

The statement "(210-196) There is no mandatory rule in the NEC limiting the voltage drop on conductors, but the Code recommends that we consider its effect" is true because the National Electrical Code (NEC) does not have a mandatory rule for limiting voltage drop on conductors, but it does recommend considering its effect to ensure efficient and safe electrical installations.

The National Electrical Code (NEC) is a standard that provides guidelines and requirements for safe electrical installations in the United States. While the NEC provides rules and regulations on many aspects of electrical installations, it does not mandate a specific limit for voltage drop on conductors.

Voltage drop refers to the reduction in voltage that occurs as electrical current flows through a conductor, due to its resistance. Excessive voltage drop can result in reduced performance of electrical equipment and appliances, as well as increased energy consumption.

Learn more about NEC limiting: https://brainly.com/question/30323573

#SPJ11

Answer:

Yellow light

Explanation:

The flashing yellow light means: "proceed with caution." Traffic facing the yellow light has the right-of-way, but oncoming traffic usually also has a flashing yellow light, and cross-traffic will have a flashing red light.

YELLOW—A yellow signal light warns you that the red signal is about to appear. When you see the yellow light, you should stop, if you can do so safely. If you can't stop, look out for vehicles that may enter the intersection when the light changes. FLASHING YELLOW— What does a flashing yellow light mean?

Hope this helped! Have a nice day!

Please give Brainliest when possible!

:3

Answer:

final temperature = 26.5°

Explanation:

Initial volume of water is 1 x 1 x 1 = 1 \(m^{3}\)

Initial temperature of water = 20° C

Density of water = 1000 kg/\(m^{3}\)

volume of copper block = 0.46 x 0.46 x 0.46 = 0.097 \(m^{3}\)

Initial temperature of copper block = 100° C

Density of copper = 8960 kg/\(m^{3}\)

Final volume of water = 1 - 0.097 = 0.903 \(m^{3}\)

Assumptions:

mass of water remaining in the tank will be density x volume = 1000 x 0.903 = 903 kg

specific heat capacity of water c = 4186 J/K-kg

heat content of water left Hw = mcT = 903 x 4186 x 20 = 75.59 Mega-joules

mass of copper will be density x volume = 8960 x 0.097 = 869.12 kg

specific heat capacity of copper is 385 J/K-kg

heat content of copper Hc = mcT = 869.12 x 385 x 100 = 33.46 Mega-joules

total heat in the system = 75.59 + 33.46 = 109.05 Mega-joules

this heat will be distributed in the entire system

heat energy of water within the system = mcT

where T is the final temperature

= 903 x 4186 x T = 3779958T

for copper, heat will be

mcT = 869.12 x 385 = 334611.2T

these component heats will sum up to the final heat of the system, i.e

3779958T + 334611.2T = 109.05 x \(10^{6}\)

4114569.2T = 109.05 x \(10^{6}\)

final temperature T = (109.05 x \(10^{6}\))/4114569.2 = 26.5°

Ragman assigns the mission "Database - Part 1" in Escape From Tarkov. You are asked to get the cargo manifests for Goshan, OLI, and IDEA from Interchange. Contents. Database for Escape from Tarkov: Part 1 Quest Information.

You can keep information on a certain topic in an organized way using a database. It's fantastic when you need to keep a computer system's worth of searchable data or information. Many systems in use today employ databases.

A database is used to store user information on nearly all popular websites with a large user base and almost every online store that sells things. Most databases comprise one or more tables, each of which may have a number of unique fields.

To know more about Database, visit:

https://brainly.com/question/518894

#SPJ4

Answer:

is it a free point? or just a question if it is kindly respond

The terminal combinations that would show an open circuit if a hermetic compressor with an internal overload device were to be open due to an overheated compressor are:

a. common to start

b. common to run

Although it is less frequently used in significant industrial or commercial applications, the term "hermetic compressor" refers to a type of compressor that is still employed on occasion. The casing of a hermetic compressor is welded shut, completely isolating it from its surroundings. Any method won't work to get to it.

When used alone, the word "hermetic" typically refers to an airtight seal. It describes how a compressor is completely isolated from its operating environment when used in relation to a compressor. As a result, flooding and slugging are reduced because there are no spills or debris infiltration issues.

Learn more about hermetic compressor

https://brainly.com/question/26883041

#SPJ4

The heat flow from the surface to the room can be calculated using the Stefan-Boltzmann law. The equation is given by:

Where:

Q = heat flow from the surface to the room (W) ε = gray-body surface emissivity (unitless) σ = Stefan-Boltzmann constant (5.67 x 10^-8 Wm^-2K^-4) A = surface area of the pipe (m^2) Ts = surface temperature of the pipe (K) Tr = temperature of the room (K)

Therefore, the heat flow from the surface to the room can be calculated as follows:

Learn more about ley de Stefan-Boltzmann:

https://brainly.com/question/18273651

#SPJ4

Answer:

SECTION LEARNING OBJECTIVES

By the end of this section, you will be able to do the following:

Distinguish between static friction and kinetic friction

Solve problems involving inclined planes

Section Key Terms

kinetic friction static friction

Static Friction and Kinetic Friction

Recall from the previous chapter that friction is a force that opposes motion, and is around us all the time. Friction allows us to move, which you have discovered if you have ever tried to walk on ice.

There are different types of friction—kinetic and static. Kinetic friction acts on an object in motion, while static friction acts on an object or system at rest. The maximum static friction is usually greater than the kinetic friction between the objects.

Imagine, for example, trying to slide a heavy crate across a concrete floor. You may push harder and harder on the crate and not move it at all. This means that the static friction responds to what you do—it increases to be equal to and in the opposite direction of your push. But if you finally push hard enough, the crate seems to slip suddenly and starts to move. Once in motion, it is easier to keep it in motion than it was to get it started because the kinetic friction force is less than the static friction force. If you were to add mass to the crate, (for example, by placing a box on top of it) you would need to push even harder to get it started and also to keep it moving. If, on the other hand, you oiled the concrete you would find it easier to get the crate started and keep it going.

Figure 5.33 shows how friction occurs at the interface between two objects. Magnifying these surfaces shows that they are rough on the microscopic level. So when you push to get an object moving (in this case, a crate), you must raise the object until it can skip along with just the tips of the surface hitting, break off the points, or do both. The harder the surfaces are pushed together (such as if another box is placed on the crate), the more force is needed to move them.

A C programme that uses recursion to calculate power

You will discover how to use recursion to determine the power of a number in this example.

You should be familiar with the following C programming concepts in order to comprehend this example:

Functions in C

User-defined functions in C

Recursive C

A loop can also be used to determine a number's power.

Use the pow() library function to determine the power of an integer when it has been raised to a decimal value.

How is power determined in recursion?

Example: Using recursion, a programme can increase computer power.

Use the pow() function to determine the power of any number. result is equal to pow(base, exponent);

Learn more about power here:

https://brainly.com/question/14379882

#SPJ4

Fine grained of alkali igneous rocks cannot be used in cement because of the volume expansion caused by the Alkali-silica reaction, fine-grained igneous rocks cannot be used as aggregates in cement.

Extrusive igneous rocks have a fine-grained or aphanitic texture, with grains that are too small to see without a magnifying glass. The fine-grained texture suggests that the rapidly cooling lava did not have enough time to form large crystals. A petrographic microscope can be used to examine these tiny crystals.

The texture of an igneous rock (fine-grained vs coarse-grained) is determined by the rate at which the melt cools: slow cooling produces large crystals, while fast cooling produces small crystals.

The chemical reaction that occurs in both alkali cations and hydroxyl ions in the pore solution of hydrated cement paste and certain reactive silica phases present in concrete aggregates is known as the alkali-silica reaction (ASR).

Learn more about cement on:

https://brainly.com/question/14323034

#SPJ1

Their main job is to chair the meetings of the organisation. The Treasurer has overall responsibility for the organisation's finances. Their main job is keeping financial records. The Secretary is responsible for keeping people informed about the organisation's activities.

Answer:

Yeah like he/she said?

Explanation:

ugh

Answer:

Shallow foundations, often called footings, are usually embedded about a metre or so into soil. ... Another common type of shallow foundation is the slab-on-grade foundation where the weight of the structure is transferred to the soil through a concrete slab placed at the surface.

Explanation:

Because I said so.

Answer:

C) a winding connected in series with the armature.

Explanation:

In a series motor, an electromagnet is used as a stator to generate its magnetic field. The field coil of this stator are connected through a commutator in series with the rotor windings. This stator which is the armature windings will conduct AC even on a DC machine, due to the  periodically reverses current direction (commutation) or due to electronic commutation (as in brushless DC motors).

Answer:

Discuss how you could measure Earth's diameter using nothing but a shadow-casting stick, a protractor, and a car's trip odometer if on a road trip between two cities that are approximately on the same line of constant longitude with a relatively straight shot of road connecting them.

Explanation:

The distance travelled as read from the car's odometer will give the diameter of the earth.

Longitude lines are imaginary lines which divides the earth into two hemispheres.

To determine the diameter of the earth, the car's trip odometer is set at zero from the first city at the start of the journey.

At midday along the straight road, the shadow-casting stick will cast no shadow.

At the end of the journey to the second city, the distance travelled is read from the car's odometer which then gives the diameter of the earth.

Therefore, the distance travelled as read from the car's odometer will give the diameter of the earth.

Learn more about diameter of the earth at: https://brainly.com/question/15118032

#SPJ2

. The electric field at the observation point (1, 1, -1) due to the given charge distributions is approximately 1448.59 N/C.

Given:

Surface charge density of the plane (σ_plane) = 15 nC/m²,

Linear charge density of the line (λ_line) = 10 mC/m²,

Charge of the point charge (q_point) = 5 nC,

Observation point coordinates (x1, y1, z1) = (1, 1, -1),

Coordinates of the plane charge: x = 0, y = 2.

First, let's calculate the electric field due to the plane charge:

E_plane = σ_plane / (2ε₀)

       = (15 * 10^-9 C/m²) / (2 * 8.854 * 10^-12 C²/(Nm²))

       = 848.68 N/C (approximately)

Next, let's calculate the electric field due to the line charge. Since the line charge is along the y-axis (from y=0 to y=2), the x and z components of the electric field will be zero.

r_line = √((x1-x2)² + (y1-y2)² + (z1-z2)²)

      = √((1-0)² + (1-2)² + (-1-0)²)

      = √3

E_line = λ_line / (2πε₀r)

      = (10 * 10^-3 C/m²) / (2 * π * 8.854 * 10^-12 C²/(Nm²) * √3)

      = 598.41 N/C (approximately)

Finally, let's calculate the electric field due to the point charge:

r_point = √((x1-x2)² + (y1-y2)² + (z1-z2)²)

       = √((1-0)² + (1-0)² + (-1-0)²)

       = √3

E_point = k * q_point / r²

       = (9 * 10^9 Nm²/C²) * (5 * 10^-9 C) / (3)

       = 1.5 N/C

Now, let's calculate the total electric field at the observation point by summing up the contributions from each charge distribution:

E_total = E_plane + E_line + E_point

       = 848.68 N/C + 598.41 N/C + 1.5 N/C

       = 1448.59 N/C (approximately)

To know more about electric field refer for :

https://brainly.com/question/19878202

#SPJ11

Answer:

21.6 kw

Explanation:

Given data:

m = 50 kg/s

Inlet pressure (p1) = 2 bar

outlet pressure(p2) = 6.2 bar

suction ( h1 ) = -2.2 m

delivery ( h2 ) = 8.5 m

d1 = 200 mm = 0.2 m

d2 = 100 mm = 0.1 m

Vs of water = 0.001 m^3/kg

next we have to determine the Q value

Q = V*A

Q = 0.001 * 50 = 0.05 m^3/s

next we have to calculate the various V's

V1 = Q/A1 = \(\frac{0.05*4}{\pi *0.2^2}\)  = 1.59 m/s

V2 = Q/A2 = \(\frac{0.05*4}{\pi *0.1^2}\) = 6.37 m/s

Determine the capacity of the electric motor

attached below is the detailed solution

The moon phase refers to the different shapes or appearances of the moon as seen from Earth. The moon's phase is determined by its position in relation to the sun and Earth, and the amount of sunlight that is reflecting off its surface. The different moon phases are:

The moon's phases repeat in a cycle that lasts about 29.5 days.

Learn more about the phase of the moon, here https://brainly.com/question/2285324

#SPJ4

Answer:

The values shown in the table below are valid only for the conditions under which they were determined (usually room temperature and atmospheric pressure using a 2 inch tube with spark ignition). The flammability range of most materials expands as temperature, pressure and container diameter increase. All concentrations in percent by volume.

GasLELUELAcetone2.613Acetylene2.5100Acrylonitrile317Allene1.511.5Ammonia1528Benzene1.37.91.3 Butadiene212Butane1.88.4n Butanol1.7121 Butene1.610Cis 2 Butene1.79.7Trans 2 Butene1.79.7Butyl Acetate1.48Carbon Monoxide12.574Carbonyl Sulfide1229Chlorotrifluoro ethylene8.438.7Cumene0.96.5Cyanogen6.632Cyclohexane1.37.8Cyclopropane2.410.4Deuterium4.975Diborane0.888Dichlorosilane4.198.8Diethylbenzene0.8 1.1 Difluoro 1 Chloroethane914.81.1 Difluoroethane5.117.11.1 Difluoro ethylene5.521.3Dimethylamine2.814.4Dimethyl Ether3.4272.2 Dimethyl propane1.47.5Ethane312.4Ethanol3.319Ethyl Acetate2.211Ethyl Benzene16.7Ethyl Chloride3.815.4Ethylene2.736Ethylene Oxide3.6100Gasoline1.27.1Heptane1.16.7Hexane1.27.4Hydrogen475Hydrogen Cyanide5.640Hydrogen Sulfide444Isobutane1.88.4Isobutylene1.89.6Isopropanol2.2 Methane517Methanol6.736Methylac etylene1.711.7Methyl Bromide10153 Methyl 1 Butene1.59.1Methyl Cellosolve2.520Methyl Chloride717.4Methyl Ethyl Ketone1.910Methyl Mercaptan3.921.8Methyl Vinyl Ether2.639Monoethy lamine3.514Monomethy lamine4.920.7Nickel Carbonyl2 Pentane1.47.8Picoline1.4 Propane2.19.5Propylene2.411Propylene Oxide2.837Styrene1.1 Tetrafluoro ethylene443Tetrahydrofuran2 Toluene1.27.1Trichloro ethylene1240Trimethylamine212Turpentine0.7 Vinyl Acetate2.6 Vinyl Bromide914Vinyl Chloride422Vinyl Fluoride2.621.7Xylene1.16.6

Answer:

I TOLD YOU I DID NOT UNDERSTAND PLEASE,

Explanation:

The covers and guardrails are required in all of the following areas except ditches.

Yes, they do need a covers and/or guardrails and it is one that is known or shall be provided to help in the protection of personnel from the hazards that pertains to open pits, tanks, vats and others.

Note that they are often needed that is covers and/or guardrails need to be provided to help to protect personnel.

Therefore, The covers and guardrails are required in all of the following areas except ditches.

Learn more about guardrails from

https://brainly.com/question/12757849

#SPJ1

Technician A and Technician B are both right. OHC (Overhead Camshaft) cylinder heads and Pushrod engine cylinder heads often have oil galleries in them. The cylinder heads play an important role in the functioning of the engine by closing and opening the valves and containing the combustion chambers.

The cylinder heads contain coolant passages and oil galleries that help cool the engine and lubricate the internal moving parts of the engine respectively. OHC (Overhead Camshaft) cylinder heads have oil galleries in them. The camshaft of an OHC engine is placed above the cylinder head. Therefore, the camshaft and the cylinder head are connected through the oil galleries to ensure adequate lubrication of the camshaft.Pushrod engine cylinder heads also have oil galleries in them. In a pushrod engine, the camshaft is located inside the engine block and connected to the cylinder head through pushrods.

To know more about galleries visit:

https://brainly.com/question/18456687

#SPJ11

Based on  the data given, the regression equation y on-x is y = 3/4x + 1.

y = (3/4)x + 100

For more such questions on Regression:

https://brainly.com/question/14230694

#SPJ8

In the two scenario above concerning port fuel-injection and sequential fuel injectors, only Technician b is correct.

A vehicle often has one fuel injector per cylinder and if one has a four-cylinder car, it would also have four fuel injectors.

Note that Fuel-pressure regulators that are found on a port fuel-injected systems is one that often work with injector pressures that is said to be of 30 to 55 PSI.

Learn more about Technician from

https://brainly.com/question/5122191

Adapting strategy and tactics to diverse building materials and engineering changes requires a deep understanding of their properties, behavior, and interaction with forces, enabling informed decision-making for successful adaptation.

The key to adapting strategy and tactics to different types of building materials and engineering changes is a comprehensive understanding of the specific materials and engineering principles involved. This includes knowledge of their properties, behavior, strengths, weaknesses, and how they interact with various forces and environments. With this understanding, one can effectively analyze and assess the implications of different materials and engineering changes, and make informed decisions on the appropriate strategies and tactics to employ for successful adaptation. Flexibility, continuous learning, and keeping up with advancements in the field are also important in adapting to evolving building materials and engineering practices.

To learn more about building materials visit:

https://brainly.com/question/6203278

#SPJ11

Scientists use a variety of methods to learn about the layers deep inside Earth. One way is by studying seismic waves, which are waves of energy that travel through the Earth's interior during earthquakes.

By analyzing how seismic waves behave as they pass through different layers of the Earth, scientists can infer the composition and properties of each layer. Another way is by examining rocks and minerals that have been brought to the surface by volcanic activity or mountain building. By analyzing the composition of these rocks, scientists can learn about the deeper layers from which they originated. Additionally, scientists use computer models and simulations to study the behavior and composition of the Earth's interior.

To know more about earthquakes click here:

brainly.com/question/29500066

#SPJ4

Answer:80 kj

Explanation:The kinetic energy of a moving body is given by,

Here, m is mass of the body, v is its velocity.

Given,   m= 1600-kg and v = 10 m/s.

Substituting these values in above equation, we get

In kilojoules,

Answer:

Computer programming is where you learn and see how computers work. People do this for a living as a job, if you get really good at it you will soon be able to program/ create a computer.

Explanation:

Hope dis helps! :)

2.4 8 cubic yards of concrete do you need to order to pour 32 transformer pads that are 35 inches wide by 28 inches long by 3% inches high.

What is transformer?
A transformer is an electrical device used for changing the amount of voltage in an alternating current (AC) circuit. It works by converting electrical energy from one voltage level to another, without changing the frequency. Transformers are used in a variety of applications, from powering electrical equipment to stepping up or down voltage in a power distribution system. Transformers come in many shapes and sizes and can be designed to meet specific needs. The basic components of a transformer are the core, primary and secondary windings, and the insulation system. The core provides a magnetic path for the electricity to travel through, while the windings carry the electrical current. The insulation system prevents any electrical leakage.

To learn more about transformer
https://brainly.com/question/23563049

#SPJ4

Explanation:

1. Ensure all circuits are de-energized before beginning work (29 CFR 1926.416(a)(3)).

2. Controls to be deactivated during the course of work on energized or de-energized

equipment or circuits must be tagged (29 CFR 1926.417(a)).

3. Employees must be instructed to recognize and avoid unsafe conditions associated with

their work (29 CFR 1926.21(b)(2)).