You are designing a lever to lift an object that weighs 500N. The lever exerts the output force 1 m from the fulcrum. How far from the fulcrum must an effort force of 250 N be applied to lift the object? Show your work.
Answers
A lever to lift an object that weighs 500N. The lever exerts the output force 1 m from the fulcrum.
To solve this problem, we can use the formula for the mechanical advantage of a lever
Mechanical Advantage = Output Force / Input Force
We know that the output force is 500 N and the input force is 250 N. Therefore, the mechanical advantage is
Mechanical Advantage = 500 N / 250 N
Mechanical Advantage = 2
Next, we can use the formula for the distance from the fulcrum to the input force
Distance from fulcrum to input force = Output Force distance / Mechanical Advantage
We know that the output force distance is 1 m. Therefore, the distance from the fulcrum to the input force is
Distance from fulcrum to input force = 1 m / 2
Distance from fulcrum to input force = 0.5 m
Hence, an effort force of 250 N must be applied 0.5 m from the fulcrum to lift the object that weighs 500N.
To know more about fulcrum here
https://brainly.com/question/4493014
#SPJ1
Related Questions
A quarterback throws a ball at 50.00 m/s,and reaches the receiver 0.56 seconds later.What is the distance from the quarter back to the receiver
Answers
Answer: 64 m is the maxium distance the ball can travel
Module 3 Discussion!
After reading Ch.12 and 13 of the text (The essentials of Finance and Accounting for nonfinancial managers/ Third Edition) on Strategy and Financial Forecasting, watching the SWOT video based on Paley’s Products from the Ratio Analysis in Module 2 and the additional narrative information in Appendix C, Phase
Create a SWOT analysis that will reflect the TOWS analysis as described in Ch. 12 of the text. The purpose of the SWOT analysis is to lay out several issues and possibilities to be considered in Paley’s strategic planning. The strengths and weaknesses are internal issues, whereas the opportunities and threats are external.
The second part of the analysis is to create actions based on the SWOTs. This is sometimes called a TOWS analysis and is done by comparing the boxes, two at a time:
Offensive actions come from strengths that link to opportunities, so a specific strength can be applied to exploit an opportunity.
Adjusting actions come from addressing weaknesses, which then can be used to exploit opportunities that previously had not been possible.
Turnaround actions come from weaknesses that link to threats. These are high-risk issues where a priority needs to be given to addressing the weakness to minimize the vulnerability.
Defensive actions come from threats that link to strengths. These are latent issues because if the threat materializes, an already-existing strength is available to counter it.
Additional actions can be included to address other issues not directly identified in the SWOTs.
3. From the actions identified in part 2, pick 3-5 strategic actions that you feel Paley must achieve or at least start in the upcoming year and state your reasons for including them.
Attach your completed SWOT form and list of strategic actions with supporting logic and facts from the case as your answer for this discussion question. These actions are the foundation for the strategic plan
Answers
SWOT Analysis Strengths- Paley’s Products has a low overhead cost with the company operating at a high level of efficiency, resulting in competitive pricing.- They have a team of experienced employees who have worked in the industry for several years.- They have a variety of products in the portfolio that can satisfy customers from different sectors.- They are reputable and have a loyal customer base.Weaknesses- They have been slow to adopt new technology, and this may be a disadvantage to the company.- Limited marketing and sales promotion are affecting their sales revenue.-
They depend on a few key customers for the bulk of their sales revenue, leaving them vulnerable to market changes.Opportunities- Expansion of the product line to include unique products.- The establishment of strategic partnerships with other businesses in the industry.- Exploration of new markets, such as international markets.- Improvement of marketing techniques to increase brand awareness.Threats- Changes in consumer preferences towards environmentally friendly products.- Increase in competition from other businesses in the industry.- Fluctuating market prices for raw materials that may lead to price increases.
Strategic Actions to be taken by Paley Products1. Development of an E-commerce platform to allow online transactions with customers. The E-commerce platform will enable Paley to reach a wider customer base, expand its reach, and increase sales revenue.2. Investment in the research and development of new environmentally friendly products. Paley will remain competitive and cater to the needs of consumers who prefer green products.3. Establishment of strategic partnerships with other businesses in the industry to leverage the strength of other companies in the industry and to develop new products or increase market share.4. Improvement of marketing techniques to increase brand awareness and improve visibility. A marketing strategy that incorporates social media and other digital channels can help promote the brand to potential customers.5. Expansion into international markets. This will enable Paley to diversify its customer base and generate more revenue. Paley can start by targeting nearby countries, then expand globally as they gain more experience and financial stability.
Learn more about SWOT Analysis:
https://brainly.com/question/25066799
#SPJ11
a radio station broadcasts on the frequency of 102.3 mhz. a. what is the wavelength of this broadcast? b. what is the photon energy of this radiation?
Answers
The wavelength of the radio broadcast is 2.93 meters. The photon energy of the radio broadcast is 6.79 x \(10^{26}\) joules.
The wavelength of the radio broadcast can be calculated using the formula:
wavelength = speed of light / frequency
The speed of light in a vacuum is approximately 3.00 x \(10^8\) meters per second. We need to convert the frequency from megahertz (MHz) to hertz (Hz):
102.3 MHz = 102.3 x \(10^6\) Hz
Plugging in the values, we get:
wavelength = (3.00 x \(10^8\)m/s) / (102.3 x \(10^6\) Hz)
wavelength = 2.93 meters
Therefore, the wavelength of the radio broadcast is 2.93 meters.
b. The photon energy of the radio broadcast can be calculated using the formula:
energy = Planck's constant x frequency
Planck's constant is approximately 6.63 x \(10^{34}\) joule-seconds. Again, we need to convert the frequency from megahertz to hertz:
102.3 MHz = 102.3 x \(10^6\) Hz
Plugging in the values, we get:
energy = (6.63 x \(10^{34}\) J·s) x (102.3 x \(10^6\) Hz)
energy = 6.79 x \(10^{26}\) joules
Therefore, the photon energy of the radio broadcast is 6.79 x \(10^{26}\)joules.
Learn more about photon energy ,
https://brainly.com/question/2393994
#SPJ4
a truck travels down the highway at a speed of 100km/hr how long does the trip last if the truck covers 2200 km
Answers
It'll last 20 hours. If it travels 110 miles in one hours, 110 times 20 equals 2,200.
Can someone please shows me the steps and answer. Urgent!
Answers
A car traveling at a steady speed of 30m/s along a motorway overtakes a coach traveling in the same direction at 25m/s.how far ahead of the coach will the car beA.1 minutes after over takingB.30 minutes after over taking
Answers
A car traveling at a steady speed of 30m/s along a motorway overtakes a coach traveling in the same direction at 25m/s.
A. 1 minute after overtaking, the car will be 300 meters ahead of the coach.
B. 30 minutes after overtaking, the car will be 9000 meters ahead of the coach.
The car is traveling 5 m/s faster than the coach. This means that every second, the car gains 5 meters on the coach. After 1 minute, or 60 seconds, the car will have gained 300 meters on the coach. After 30 minutes, or 1800 seconds, the car will have gained 9000 meters on the coach.
Learn more about distance, speed, and time relationships in kinematics here:
https://brainly.com/question/28973409
#SPJ11.
1. suppose that you have two boxes one is 20 cm x 20 x 20 cm. the other is 20cm x 20 cm x 40 cm.
a.) how does the pressure of the air on the outside of the two boxes compare?
b.) how does the magnitude of the total force of the air on two boxes compare?
2. in a certain internal combustion engine 0.0021 m^3 of the air at atmospheric pressure and 303 k is rapidly compressed to a pressure of 20.1 x 10^5 pa and volume of 0.0003 m^3 what is the final temperature of the compressed gas?
3.) a tank truck takes a load of 45,725 l of gasoline in houstin where temp is 28.0 c the truck delivers its load in minneapolis where the temp is -12.0c
a.) how many liters of gas does the truck deliver
b.) what happened to the gas?
please help me answer one of these or all if you can its due tmro thank you so much
Answers
The pressure will be the same if each of these boxes have the same elevation. On the second box, the air's overall force will be greater.
Although I'm sure some academics would be furious about this, it helps me to conceive of air as water. However, as air is a considerably lighter fluid than water, this replacement is acceptable. Because there is the same quantity of water on each submarine, the pressures will be the same if there are two of them at the ocean's bottom. But a larger sub will be subjected to more force, which increases the likelihood of it bowing. I would take into consideration the units of pressure and force per unit area as the force idea is difficult to express.
Since we are aware that pressure is constant, we may set them equal by using the formulas P1=P2 and P1=F1/A1 and P2=F2/2(A1).
F1/A1=F2/2A1
It is evident that F2=2F1.
Learn more about Pressure here:
https://brainly.com/question/29341536
#SPJ4
CAN PEOPLE PLEASE HELP, I NEED TO GET TO THE NEXT LEVEL OR WHATEVER ITS CALLED BUT I NEED 5 BRAINLIEST IN 2 DAYS, I ALREADY HAVE 7 BUT THAT DOSENT COUNT IG, IF YOU HELP ILL RETURN THE FAVOR AND GIVE YOU BRAINLIEST ON YOUR AWENSERS OR QUESTIONS........ ILL AWENSER ONE OF YOUR QUESTIONS AND YOU MAKE ME BRAINLIEST? THXX
Answers
Answer:
answer the question i have asked go to my account
Explanation:
can i get brainliest
Answer:
yes you can go on your account
A stream moving with 2 m/s reaches a point where the cross-section area of the stream decreases to one-fourth of the original area. What is the water speed in this narrowed portion of the stream?
Answers
Given,
Initial speed is v=2 m/s
The cross sectional area reduces to 1/4 of the original area
To find
The speed of water at the narrowed portion.
Explanation
Let the original area be A
Let the speed at the narrowed portion be u
By conservation lawwe have,
\(\begin{gathered} v\times A=u\times\frac{1}{4}A \\ \Rightarrow2\times4=u \\ \Rightarrow u=8\text{ m/s} \end{gathered}\)Conclusion
The speed at the narrowed portion is 8 m/s
List the elements mentioned from hydrogen to iron in the order of their fusing temperature.
Answers
Explanation:
H
Hydrogen
-259.14 -252.87 0.00008988 (gas, 273K)
2
He
Helium
-272.20 (under pressure) -268.934 0.0001785 (gas, 273K)
3
Li
Lithium
180.54 1347 0.534
4
Be
Beryllium
1278 2970 1.8477
5
B
Boron
2300 3658 2.34
6
C
Carbon
3527 4827
(sublimes) 2.260 (graphite)
3.513 (diamond)
7
N
Nitrogen
-209.86 -195.8 0.0012506 (gas, 273K)
8
O
Oxygen
-218.4 -182.96 0.001429 (gas, 273K)
9
F
Fluorine
-219.62 -188.14 0.001696 (gas, 273K)
10
Ne
Neon
-248.67 -246.05 0.00089994 (gas, 273K)
11
Na
Sodium
97.81 882.9 0.971
12
Mg
Magnesium
648.8 1090 1.738
13
Al
Aluminum
660.37 2467 2.698
14
Si
Silicon
1410 2355 2.329
15
P
Phosphorus
44.1 (white)
410 (red, under pressure) 280 (white) 1.82 (white)
16
S
Sulfur
113 (α)
119 (b)
106.8 (g) 444.67 2.070 (α)
1.957 (b)
17
Cl
Chlorine
-100.98 -33.97 0.003214 (gas, 273K)
18
Ar
Argon
-189.37 -185.86 0.001784 (gas, 273K)
19
K
Potassium
63.65 774 0.862
20
Ca
Calcium
839 1484 1.55
21
Sc
Scandium
1541 2831 2.989
22
Ti
Titanium
1660 3287 4.54
23
V
Vanadium
1887 3377 6.11 (292 K)
24
Cr
Chromium
1857 2672 7.19
25
Mn
Manganese
1244 1962 7.44
26
Fe
Iron
1535 2750 7.874
27
Co
Cobalt
1495 2870 8.90
28
Ni
Nickel
1453 2732 8.902 (298 K)
29
Cu
Copper
1083.4 2567 8.96
30
Zn
Zinc
419.58 907 7.133
31
Ga
Gallium
how do the properties of waves correspond with observations of waves?
Answers
Answer:
no sabo por q no mi entender
Three 44-ohm resistors are connected in parallel with an ideal 12-volt battery. What is the equivalent resistance of the circuit?
Answers
Answer:
Explanation:
1/Rtotal = 1/r1 +1/r2 +1/r3
1/Rtotal = 1/44 + 1/44 + 1/44
1/Rtotal = 3 /44
1/Rtotal = 0.0681818182
1/0.0681818182 = Rtotal
14.66666666666666666 = Rtotal
14 \(\frac{2}{3}\) ohms = Rtotal
at a particular instant, a hot air balloon is 210 m in the air and descending at a constant speed of 3.5 m/s. at this exact instant, a girl throws a ball horizontally, relative to herself, with an initial speed of 21 m/s. when she lands, where will she find the ball? ignore air resistance. (find the distance, in meters, from the girl to the ball.)
Answers
The ball which is thrown with a speed of 21 m/s, travels a distance of 129.99 m in the horizontal direction.
Therefore, the vertical component of the ball's motion will be determined by the force of gravity and the initial vertical speed of the balloon.
We can use the following kinematic equation to determine how long it takes for the ball to fall to the ground:
h = ut + 1/2 * g * t^2
where h is the initial height of the ball (equal to the height of the balloon which is 210 m).
u is the initial velocity of the ball in the vertical direction which is 3.5 m/s.
g is the acceleration due to gravity (approximately 9.8 m/s^2),
and t is the time it takes for the ball to fall to the ground.
Plugging in the values we know, we get:
210 = 3.5 * t + 1/2 * 9.8 * t^2
4.9 t^2 + 3.5 t - 210 = 0
t = 6.19 seconds
Now we can use the time it takes for the ball to fall to the ground to determine how far it travels horizontally, given its initial horizontal velocity of 21 m/s. We can use the following equation:
d = v * t
where d is the horizontal distance traveled by the ball, v is its initial horizontal velocity, and t is the time it takes to fall to the ground (which we just calculated).
Plugging in the values we know, we get:
d = 21 * 6.19
d ≈ 129.99 meters
Therefore, the girl will find the ball approximately at a distance of 129.99 meters away from her when she lands after throwing the ball horizontally.
Learn more about the kinematic equation:
https://brainly.com/question/28712225
#SPJ11
3. Twelve waves pass a dock in 3.60 If the waves are traveling at 19.5 m/s , what is the wavelength of the waves?
Answers
Answer:
65m
Explanation:
Twelve waves pass a dock in 3.60 If the waves are traveling at 19.5 m/s , what is the wavelength of the waves?
Velocity of a wave is expressed as;
V = frequency × wavelength
Given
Velocity = 19.5m/s
Frequency is the number of oscillations completed in 1sec, hence
Frequency= 3.6/12
Frequency = 0.3
Wavelength = vel/freq
Wavelength = 19.5/0.3
Wavelength = 65m
what is a rocket engine that fires against the direction a spacecraft is headed so the spacecraft slows down?
Answers
The rocket engine that fires against the direction a spacecraft is headed so the spacecraft slows down is called Retro engine.
Spacecraft are the space automobiles that might be capable of flying out of doors of the Earth’s ecosystem in the area. They offer us a method of transportation from the Earth to the area and objects in it. There may be numerous spacecraft that are familiar to most of people e.g. Apollo 11 which took Neil Armstrong and his group to the Moon.
Crewed Spacecraft – Crewed spacecraft are the ones that carry people to the area. There have been several crewed spacecraft to the area consisting of Vostok 1 – the first crewed spacecraft in records dispatched by way of the United States of America.
Earth-Orbit Satellites – all of the satellites, which orbit across the Earth, fall in this class. The maximum tremendous satellite in orbit on the Earth is Hubble Telescope.
Space Probe – these are unmanned spacecraft that might be fitted with medical instruments for exploring objects in space e.g. planets, Moon, and solar.
Learn more about spacecrafts here:- https://brainly.com/question/28175986
#SPJ4
Write an algorithm that calculate the time a train need to arrive at a detination given peed and ditance
Answers
An algorithm that calculates the time a train needs to arrive at a destination given speed and distance \(Time=\frac{Distance}{Speed}\).
What is Speed?The amount of the shift in approach per unit of time or the size of the displacement over time for an object can be used to describe speed, which would be a scalar quantity in everyday language and kinematics.
The maximum speed that can be maintained when a period grows closer to zero is the starting speed.
By dividing the object's distance traveled by the duration of the interval, the mean pace of the object for the given period is calculated. Speed and velocity are not always the same thing.
The algorithm to calculate the time required will be,
Let the distance covered by the train is D and the speed of the train be S.
Then, the time taken by the train will be,
T = D/S
Here, D is the distance and S is the speed.
To know more about Speed:
https://brainly.com/question/28224010
#SPJ1
One one-thousandth is expressed by which prefix?
Answers
Answer:
With the prefix milli
Explanation:
A cross country skier moves from location A to location B to location C to location D. Each leg of the back and forth motion takes 1 minute to complete; the total time is 3 minutes.
What is the distance travelled by the skier in the first minute?
What is the displacement of the skier in the first minute?
What is the distance travelled by the skier in the first two minutes?
Please help it’ll be greatly appreciated!!
Answers
Answer:
1. 160
2. 0
3. 120
Explanation:
For a given potential difference, a bigger resistance means a smaller __________ through a component. What one word completes this sentence
Answers
For a given potential difference, a bigger resistance means a smaller current through a component.
What is the resistance in a circuit?Resistance in an electrical circuit is a measure of the opposition to the flow of electric current. It is measured in units of ohms (Ω) and is represented by the symbol R in electrical equations.
The amount of resistance in a circuit can affect the amount of current flowing through it and the voltage across it. In a simple circuit, resistance is primarily determined by the materials used in the circuit, such as the wires and the components.
In a more complex circuit, resistance can also be affected by the design of the circuit, including the number of components and the way they are connected. The resistance determines the current in the circuit.
Learn more about resistance:https://brainly.com/question/29427458
#SPJ1
What is an eclipse? Definition
Answers
Answer:
An obscuring of the light from one celestial body by the passage of another between it and the observer or between it and its source of illumination.
Explanation:
If a car has traveled 24 km in 2 hours, what is its average speed?
Answers
Answer:
12km per hour
Explanation:
The formula is distance/time.
24km/2 hours = 12km/1 hour
Explanation:
average speed = distance / time
= 24km/ 2 hr
= 12 km/ hr
Hope this will be helpful to you .
Calculate the momentum of a 1kg box moving at a velocity of 50 m/s.
Answers
the momentum = m * v
m : mass
v : velocity
momentum = 1 * 50 = 50 kg.m/s
What do you put in the bowl first? milk or cereal?
Answers
Answer:
i put cereal first
Explanation:
cereal
3. Based on what you learned in this lab, describe how the earth’s surface is heated by the sun’s radiation.
Answers
Earth's surface is heated by the sun's radiation as this radiation travels through space, enters the atmosphere, and warms elements inside the earth.
What is the main source of radiation?The main source of radiation is the Sun because this produces high amounts of heat due to nuclear fusion reactions that occur in its core.
How is Earth's surface heated?Heat travels through space in form of waves.The waves then enter the atmosphere as shortwaves This radiation later hits the surface and warms it.Some of this radiation is reflected as long waves which go to the atmosphere, and makes the surface and atmosphere have a warm temperature.
Note: This question is incomplete; due to this, I provided an answer based on general knowledge.
Learn more about radiation in: https://brainly.com/question/9815840
You throw a dodge ball with a mass of 2.1 kg. The ball leaves your hand with a speed of 25 m/s. Identify the energy (PE or KE) and calculate it.
Answers
Given,
The mass of the object, m=2.1 kg
The speed of the object, v=25 m/s
Kinetic energy is the energy that an object possesses due to its motion. And potential energy is the energy that an object possesses due to its position.
The gravitational potential energy depends on the height of the object. As the change in the height of the object is not mentioned in the question, let us assume that there is no change in the potential energy.
The velocity of the object, however, changes. Thus the energy possessed by the object is the kinetic energy.
And the kinetic is given by
\(E_K=\frac{1}{2}mv^2\)On substituting the known values,
\(\begin{gathered} E_K=\frac{1}{2}\times2.1\times25^2 \\ =656.25\text{ J} \end{gathered}\)Thus the kinetic energy of the ball is 656.25 J
In the figure, a broad beam of light of wavelength 610 nm is incident at 90? on a thin, wedge-shaped film with index of refraction 1.45. An observer intercepting the light transmitted by the film sees 10.0 bright and 9.00 dark fringes along the length of the film. By how much does the film thickness change over this length?
Answers
The film thickness change over by dL = 1.99 um.
Thomas Young proposed that the superposition principle applies to light, which is a wave. His ability to demonstrate that light may interfere both positively and negatively was his biggest experimental achievement. An updated version of Young's experiment, which only differs in the source of light from the original experiment, uniformly illuminates two parallel slits in an otherwise opaque surface. The light passing through the two apertures can be seen on a distant screen. When the slit widths are substantially more than the light's wavelength, the laws of geometrical optics are upheld and the light creates two shadows and two illuminated zones on the screen.
There are 10 bright fringes
2nLa= (ma + 0.5)W
2nLb = (mb + 0.5)W
mb = ma + 9
2nLb - 2nLa = 9W
Dark fringes = 9
dL = 9 × 610nm/(2 × 1.45)
Thickness film changes by dL = 1.99 um
Want to know more about fringe visit the following link;
https://brainly.com/question/12732324
#SPJ4
Unpolarized light passes through two polarizers whose transmission axes are at an angle of 35.0 ∘ with respect to each other. What fraction of the incident intensity is transmitted through the polarizers?
Answers
Approximately 67.07% of the incident intensity is transmitted through two polarizers with transmission axes at an angle of 35.0° with respect to each other, according to Malus' Law.
When unpolarized light passes through two polarizers with transmission axes at an angle of 35.0° with respect to each other, the fraction of the incident intensity transmitted can be calculated using Malus' Law. Malus' Law states:
I_transmitted = I_incident * cos²θ
where I_transmitted is the transmitted intensity, I_incident is the incident intensity, and θ is the angle between the transmission axes.
For your case, θ = 35.0°. To calculate the fraction of the incident intensity transmitted, plug this angle into Malus' Law:
I_transmitted / I_incident = cos²(35.0°)
Using a calculator, cos(35.0°) ≈ 0.8192, so:
I_transmitted / I_incident = (0.8192)² ≈ 0.6707
Therefore, approximately 67.07% of the incident intensity is transmitted through the polarizers.
learn more about Malus' Law here:
https://brainly.com/question/15554133
#SPJ11
Integrated circuits consist of electrical channels that are etched into silicon wafers. A certain proportion of the circuitry is defective due to "undercutting", which happens when too much material is etched away from the channels, resulting in un-etched portions on the boards that are too narrow. A redesigned process involving lower pressure in the etching chamber is under investigation. The goal is to reduce the undercut rate to less than 5%. Of the first 100 circuits made by the new process, only four show evidence of undercutting. True or false:
a) Since only 4% of the 100 circuits had undercut, it can be concluded that the objective has been achieved.
b) Although the sample percentages are below 5%, this could represent sampling variation, so it is possible that the target has not yet been reached.
c) There is no point in evaluating the new process, because no matter what the result is, it could only be attributed to sampling variation.
d) If we sample a large enough number of circuits and if the percentages of defective circuits are sufficiently below 5%, then it is reasonable to conclude that the objective has been achieved.
Answers
False. The objective of reducing the undercut rate to less than 5% cannot be concluded based on the sample data of four undercut circuits out of the first 100 circuits made by the new process.
The given information states that the redesigned process aims to reduce the undercut rate to less than 5%. However, in the sample of the first 100 circuits produced using the new process, only four show evidence of undercutting.
It is important to note that the sample percentage of 4% (four out of 100) is below the target rate of 5%. However, it would be premature to conclude that the objective has been achieved based solely on this sample data.
Sampling variation is a significant factor to consider when drawing conclusions from a small sample. It is possible that the observed 4% could be a result of sampling variation rather than an accurate representation of the overall undercut rate of the new process. In other words, the sample might not fully capture the true proportion of defects in the entire production.
To make a more reliable conclusion, a larger sample size would be necessary. By sampling a sufficiently large number of circuits and consistently finding percentages of defective circuits that are significantly below the 5% target, it would become reasonable to conclude that the objective has been achieved.
Learn more about redesigned process
brainly.com/question/13104616
#SPJ11
Heat is the measurement of energy from all the particles that are in a substance.
Please select the best answer from the choices provided : T/F
Answers
Explanation:
the correct answer is (true) if am not mistaking incase am wrong sorry
The dark screen has a 2-mm-diameter hole. The bulb is the only source of light. What do you see on the viewing screen?
Answers
When looking at the viewing screen with a dark screen and a 2-mm-diameter hole, you would see a small, bright spot of light.
On the viewing screen, you would see a small, bright spot of light. Since the screen is dark and there is a 2-mm-diameter hole, only the light from the bulb passing through the hole will be visible. This creates a focused beam of light that appears as a spot on the screen.
To explain this further, when light passes through a small hole, it undergoes a process called diffraction. Diffraction causes the light to spread out and interfere with itself, creating a pattern of bright and dark regions. However, in this case, since the screen is dark and there are no other sources of light, only the light passing through the hole will be visible on the screen.
The size of the spot on the screen will depend on the size of the hole. In this case, with a 2-mm-diameter hole, the spot will be relatively small. The brightness of the spot will depend on the intensity of the light emitted by the bulb.
In summary, when looking at the viewing screen with a dark screen and a 2-mm-diameter hole, you would see a small, bright spot of light.
Learn more about light at: https://brainly.com/question/104425
#SPJ11