What are some paradigms from history that have been proven inaccurate or incomplete

Two connectors that are part of the system case and connect to header pins on the motherboard are the power switch and the HDD LED activity.

So, the correct answer is B and C.

The power switch is a small button located on the front panel of the case, which allows the user to turn the computer on or off. The HDD LED activity connector is responsible for indicating the hard drive's activity through a light on the front panel.

On the other hand, the SATA power and 24-pin ATX power connectors are used to provide power to the internal components, such as the hard drives and motherboard, and the 8-pin EPS12V connector is used to provide additional power to the CPU.

These connectors are not part of the system case but rather directly connect to the power supply unit.

Hence, the answer of the question is B and C.

Learn more about connector at https://brainly.com/question/32276760

#SPJ11

Explanation:

The minimum value of insulation resistance test performed on a small extra low voltage installation is B) 2.0 MOhm. This resistance is required to ensure the safety of the installation by preventing electric shocks and other hazards.

Answer:

Some of the major application of solar energy are as follows: (a) Solar water heating (b) Solar heating of buildings (c) Solar distillation (d) Solar pumping (e) Solar drying of agricultural and animal products (f) Solar furnaces (g) Solar cooking (h) Solar electric power generation (i) Solar thermal power production (j) Solar green houses.

Answer:

The temperature gauge showing that the vehicle has been running warmer or has recently began to have issues from overheating is  an idication that your vehicle may be developing a cooling system problem.

Explanation:

Answer:idek

Explanation:u

Answer:

The golfer is at greater risk.

Explanation:

The golfer is holding a metal club. Metal is a good conductor for electricity (lightning), meaning electrons can pass through easily. Her caddy is at lesser risk because she is holding a plastic handled umbrella. Plastic is an insulator, which does not easily allow the movement of electrons to pass.

Answer:

somewhere around 34.2223 meters thick but that's what I am estimating.

The CIA triad and the Parkerian hex are the fundamental principles of information security.

Parkeriano, or Parkerian hexad: is a set of six elements of information security proposed by Donn B. Parker.

1. Confidentiality.

2. Ownership or Control.

3. Integrity.

4. Authenticity.

5. Availability.

6. Utility

The Parkerian hexagram adds three more attributes to the three classic security attributes of the CIA triangle

these are the fundamental principles of information security.

Learn more about CIA triad in  https://brainly.com/question/14697747

The feature that is not characteristic of the international style is applied ornament. This style is known for its minimalism and simplicity, often featuring geometric forms, glass walls, and prioritizing volume over mass. However, it does not typically incorporate decorative ornamentation in its design.

The feature that is not characteristic of the International Style is applied ornament. The International Style typically emphasizes geometric form, volume over mass, and glass walls, while avoiding ornate decorations or applied ornamentation.The feature that is not characteristic of the International Style is applied ornament. The International Style emerged in the early 20th century and was characterized by a focus on functionality, simplicity, and the use of modern materials and construction techniques. It emphasized a minimalist aesthetic that was devoid of unnecessary ornamentation or decoration.Geometric form, volume over mass, and glass walls are all key features of the International Style. Geometric form refers to the use of simple geometric shapes such as squares, rectangles, and circles in the design of buildings. Volume over mass refers to the use of lightweight materials and the creation of buildings with a sense of lightness and transparency. Glass walls were a key element of the International Style, allowing for greater transparency and connection between interior and exterior spaces. Applied ornament, on the other hand, was not characteristic of the International Style. Ornamentation was seen as unnecessary and superficial, and architects and designers sought to eliminate it in favor of a more functional and streamlined approach. This rejection of applied ornament was a defining characteristic of the International Style, and it has influenced architectural design to this day.

To learn more about international style click on the link below:

brainly.com/question/31090413

#SPJ11

The feature that is not characteristic of the international style is applied ornament.

The international style emphasizes simplicity, functionality, and the use of modern materials such as steel, concrete, and glass. It favors geometric forms and the use of volume over mass, as well as the incorporation of large expanses of glass walls. However, it rejects the use of decorative ornamentation, as it goes against the minimalist and rational principles of the style.

Learn more about international style: https://brainly.com/question/31587065

#SPJ11

Answer:

  0.9104

Explanation:

Suitable technology can tell you the probability.

P(-1.5≤Z≤2) ≈ 0.9104

__

A phone app gives the probability as 0.9104426667829628.

Answer:

a. will be damaged if energized

Explanation:

A hermetic compressor needs a coolant to prevent overheating of the motor. The cooling of the compressor depends on the flow of the refrigerant through the compressor hence when under a deep vacuum,  the motor winding of a hermetic compressor can overheat.  

A crankcase heater is used to prevent the mixing of refrigerant and oil at low temperatures. The mixing of refrigerant and oil can cause oil foaming in the vacuum. When under a deep vacuum,  the motor winding of a hermetic compressor can overheat if the crankcase heater is energized.

Answer:

It is used for solving optimization problems in which,given some functional,one seeks the function minimizing or minimizing it.

Explanation:

Please i need a Brainliest.

Answer:

10.203 Volts

Explanation:

For this problem, we need to understand that a series resistive circuit is simply a circuit with some type of voltage source and some resistors, in this case, R1 and R2.

First, we need to find the voltage in the circuit.  To do this, we need to find the total resistance of the circuit.  When two resistors are in series, you sum the resistance.  So we can say the following:

R_Total = R1 + R2

R_Total = 570 Ω + 560 Ω

R_Total = 1130 Ω

Now that we have R_Total for the circuit, we can find the voltage of the circuit by using Ohm's law, V = IR.

V_Total = I_Total * R_Total

V_Total = 17.9 mA * 1130 Ω

V_Total = 20.227 V

Now that we have V_Total, we can find the voltage drop across each resistor by using Ohm's law once more.  Note, that since our circuit is series, both resistors will have the same current (I.e., I_Total = I_1 = I_2).

V_Total = V_1 + V_2

V_Total = V_1 + I_2*R2

V_Total - I_2*R2 = V_1

20.227 V - (17.9 mA * 560 Ω) = V_1

20.227 V - (10.024 V) = V_1

10.203 V = V_1

Hence, the voltage drop across R1 is 10.203 Volts.

Cheers.

Answer:

B) Minimum voltage drop across meter

Explanation:

An ammeter is a measuring instrument device that is used to measure small currents flowing through a circuit in milli-ampere. The internal resistance of the milli ammeter is very low so that there would be a minimum voltage drop across the meter causing a minimum effect of the current in the circuit, this results to a measurement closer to the original value. If a high resistance is place, there would be large voltage drop therefore the current measured would be lesser than the original value.

The term you are looking for is "electromagnetic radiation." Electromagnetic radiation refers to energy in the form of waves that propagate through space, carrying both heat and light energy.

These waves can vary in wavelength and frequency, resulting in different forms of electromagnetic radiation such as radio waves, microwaves, infrared, visible light, ultraviolet, X-rays, and gamma rays. While some forms of electromagnetic radiation, like visible light and radio waves, are generally harmless, others can be dangerous. Ultraviolet (UV) radiation, for example, can cause sunburn, skin aging, and increase the risk of skin cancer. X-rays and gamma rays, which have even higher frequencies and energy, can penetrate tissues and cause damage at the cellular level, potentially leading to serious health issues if exposure is prolonged or excessive.

It's essential to be aware of the various types of electromagnetic radiation and take appropriate precautions, such as wearing sunscreen to protect against UV rays or limiting exposure to X-rays. Overall, electromagnetic radiation plays a crucial role in our daily lives, from enabling communication and technology to providing us with the warmth and light we need.

Learn more about frequency here: https://brainly.com/question/30053506

#SPJ11

Answer:

The view factor for radiation emitted by surface 2 to surface 1 is 0.1

Explanation:

Given

\(F_{12} = 0.4\)

\(A_1 = 0.01m^2\)

\(A_2 = 0.04m^2\)

Required

Determine \(F_{21}\)

To do this, we make use of the following equivalent ratio

\(A_1 * F_{12} = A_2 * F_{21}\)

Make \(F_{21\) the subject

\(F_{21} = \frac{A_1 * F_{12}}{ A_2}\)

Substitute values into the equation

\(F_{21} = \frac{0.01m^2 * 0.4}{0.04m^2}\)

\(F_{21} = \frac{0.01 * 0.4}{0.04}\)

\(F_{21} = \frac{0.004}{0.04}\)

\(F_{21} = 0.1\)

This statement is generally true. In most cases, waste piping is designed to connect to drain piping on the outlet side of traps or at other designated locations in drainage piping.

Traps are important components of plumbing systems that are designed to prevent the flow of sewer gases, insects, and other pests from entering a building through the plumbing system. They are typically installed in waste piping near the fixture that they serve, such as a sink, toilet, or shower.

The waste piping that connects to these fixtures typically leads to the inlet side of the trap, which is designed to hold a small amount of water that forms a seal to prevent sewer gases from entering the building. From there, the drain piping usually connects to the outlet side of the trap, allowing waste water to flow out of the building and into the sewer or septic system.

There may be some exceptions to this general rule, depending on the specific design of the plumbing system and local building codes. In some cases, for example, a waste line may be connected directly to a building's vent stack to improve drainage and prevent the buildup of gases. However, these types of configurations are typically designed and installed by licensed plumbers or other qualified professionals who are familiar with local plumbing codes and best practices.

In summary, while there may be some variations in the design and configuration of waste and drain piping in different plumbing systems, it is generally true that waste piping connects to drain piping on the outlet side of traps or at other designated locations in drainage piping.

To know more about drainage: https://brainly.com/question/29432940

#SPJ4

Answer:

1021c.

Explanation:

''.''

Once a Zener diode breaks down, it starts to conduct current in the reverse direction, and the voltage across the diode remains relatively constant.

This is because a Zener diode is designed to operate in the breakdown region, where it can maintain a nearly constant voltage drop across its terminals, regardless of the current flowing through it.Therefore, if an increase in applied voltage draws more current to the circuit, the voltage across the Zener diode will remain constant, as long as the current remains within the diode's specified rating. If the current exceeds the diode's rating, it may overheat and fail, or the voltage across the diode may begin to vary.

To learn more about diode click the link below:

brainly.com/question/30576988

#SPJ11

The minimum amount of work needed to remove one mole of solute from 99 moles of solvent at 1 bar and 250 °C is approximately -10,690 J.

We may use the following equation to calculate the least amount of work required to remove one mole of solute from each of the examples:

Work (W) = RT ln (Cf / Ci)

Cf = 1 mole

Ci = 99 moles

T = 250 °C + 273.15 = 523.15 K

So,

W = (8.314 J/(mol·K)) * (523.15 K) * ln (1/99)

W ≈ - 10,690 J

Cf = 1 mole

Ci = 999 moles

T = 250 °C + 273.15 = 523.15 K

So,

W = (8.314 J/(mol·K)) * (523.15 K) * ln (1/999)

W ≈ - 11,379 J

Cf = 1 mole

Ci = 1 ppm = 1/1,000,000 moles

T = 250 °C + 273.15 = 523.15 K

So,

W = (8.314 J/(mol·K)) * (523.15 K) * ln (1/(1/1,000,000))

W ≈ 0 J

Cf = 1 mole

Ci = 1 ppb = 1/1,000,000,000 moles

T = 250 °C + 273.15 = 523.15 K

So,

W = (8.314 J/(mol·K)) * (523.15 K) * ln (1/(1/1,000,000,000))

W ≈ 0 J

Thus, the minimum amount of work needed for the given scenarios are - 10,690 J, - 11,379 J, 0 J, and 0 J respectively.

For more details regarding work done, visit:

https://brainly.com/question/3902440

#SPJ4

Answer:

OneNote can be used to share  

✔ information

before the meeting.

OneNote integrates seamlessly with Outlook by placing a  

✔ link

in the meeting request.

OneNote can also be used to pass information along both  

✔ during

and after the meeting.

Answer:

b. False

Explanation:

A centimeter is a hundredth of a meter. This means 1/100 ,1 cm = 0.01 m

A kilo is 1000 grams.

The first answer is false because a hundredth isnot written well.

The second statement is false because the comparison given is of different units of measure. For distance is meters where as for weight is kilograms.

\(\boxed{ℒ_t[f(t)] =\frac{30}{{s}^{4} } - \frac{9}{s} + \frac{6}{s + 5} + \frac{1}{s - 3}} \)

This holds true because:

\(\lim_{s\to\infty} [\frac{30}{{s}^{4} } - \frac{9}{s} + \frac{6}{s + 5} + \frac{1}{s - 3}] =0 \)

[The answer is throughly verified, hence you can trust this :)]

Answer:

b i think is the correct answer

Explanation:

it was a bit hard but i used a ohms calculator

u should try it. it will help

Current is defined as the flow of electrical charge carriers, which are often electrons or electron-deficient atoms. The correct option is B.

Current is defined as the flow of electrical charge carriers, which are often electrons or electron-deficient atoms. The capital letter 'I' is a typical sign for current. The ampere, denoted by A, is the standard unit.

The relationship between current(I), resistance(R), and voltage(V) is written as:

V = IR

Given circuit has a total resistance of 10 ohms and 30 volts. Therefore, the total current that can be drawn from the circuit is,

30 volts = I × 10 ohms

I = 30/10 amp

I = 3 A

Hence, the correct option is B.

Learn more about Current:

https://brainly.com/question/13076734

#SPJ2

Answer:

Increasing following distance to Four-seconds when encountering other motorists who follow too closely  is an example of appropriate implementation of the IPDE defensive driving strategy for the  maintenance of an appropriate Safety Cushion.

Explanation:

Maintaining the required safety cushion by utilizing the IPDE defensive driving strategy to manage the nine to fifteen space driving zones involves continuous scanning.  Therefore, motorists should be able to identify objects and hazards in the driving scene, line of sight, and path of travel.  They should predict points of driving conflicts.  They should determine appropriate and safe driving actions to take, when, and where.  Finally, action is required to ensure that conflicts are avoided.

The steel-frame structural support was a main feature in the development of t the floors, roof, walls and  skyscraper.

Steel frame is known to be a form of a building method that is used along with a skeleton frame that is made up of steel columns and  I-beams.

Conclusively, This is often used  in the construction of grid to aid the floors, roof and walls of any kind of building. It is also used in the construction of skyscraper.

Learn more about structural support from

https://brainly.com/question/1145299

#SPJ1

As a local hardware store employee, I have concerns about the long-term consequences and risks of a gene drive for eliminating West Nile Virus.

Participant: A local hardware store employee

Post:

As a local hardware store employee, I have a vested interest in the well-being of the Phoenix community. I understand that the scientists from ASU are proposing the development of a gene drive to eliminate West Nile Virus in our area, and I believe it's crucial to have an open discussion about this research vision.

Firstly, I want to emphasize that I am not an expert in genetics or public health. However, I do have concerns and questions regarding the potential implementation of a gene drive for such a purpose.

My main concern revolves around the long-term consequences and potential risks associated with altering the genetic makeup of organisms, even if it is for a positive outcome like eliminating West Nile Virus. While the eradication of this disease is undoubtedly a worthy goal, we must ensure that the benefits outweigh any unintended negative effects.

Before I can fully support or oppose this research, I would like to better understand the safeguards that would be put in place to prevent any unintended ecological disruptions. What are the contingency plans if the gene drive were to have unintended consequences on non-target species? Are there measures in place to address potential resistance to the gene drive in the West Nile Virus-carrying mosquitoes? These are critical questions that must be answered to assess the feasibility and safety of this project.

Additionally, it would be crucial to involve a diverse range of stakeholders in the decision-making process. Engaging with experts in genetics, public health officials, and environmentalists, along with community members, will help ensure that all perspectives are taken into account. Transparency and inclusivity are key to fostering trust and ensuring that the decision ultimately made serves the best interests of our community.

In conclusion, while I recognize the importance of addressing the issue of West Nile Virus, I approach the proposal for a gene drive with caution. My starting position is one of skepticism and the need for further information. I believe a comprehensive risk assessment, robust stakeholder engagement, and a thorough examination of potential unintended consequences are necessary before making a final determination on supporting or opposing the project.

Learn more about Gene drive

brainly.com/question/30243090

#SPJ11

Answer:

Follows are the solution to the given question:

Explanation:

In the environment of the piles of earth, its spacecraft faces extreme temperatures:

Therefore, to prevent satellite build sustainability, a temperature control system must be used.

Its skin must be rather permeable in physiological terms.

Its shuttle's surface should have adhered to both the material well.

Whether it gets broken, it ought to be easy to repair.

All tile mostly on the cutter is composed of silicon dioxide particles, that are bonded and create a tile of very low density.

Its heat transfer is so small that even a person may hold a burning hot side on one side of the tile.

Skin that uses a rubber resin to ensure that perhaps the powers may not release the cutting that heat-treated will then the internal body.

The design requirements that led to the combination of ceramic tiles and aluminium materials for the hull of shuttle space are; discussed below.

The space shuttle experiences extreme temperatures during re-entry into the earths atmosphere. Thus, as a result, a thermal protection system must be provided to help prevent damage of the shuttle structure.

Therefore, the skin must be made up of material that has an exceptionally low thermal conductivity and also the material must be able to be firmly attached to the skin and also be able to be easily repaired in case of any damage.

Secondly, the tiles used on the space shuttle will have to be composed of silica fibers that are bonded together to generate a ceramic of low density. The thermal conductivity of the ceramic would have to be low such that if you touch one end while the other is very hot, you will not feel the hotness.

Now, the tiles will be attached to the shuttle skin with the aid of a rubbery polymer which ensures that the forces don't break the tile loose which will then expose the underlying skin to high temperatures.

Read more about some physical properties of ceramic at; https://brainly.com/question/14215109